A fire surround can make your room look very elegant

Styling Your Room Around a Fire Surround (and How to Fit It)

A fire surround is usually the first thing people notice when they walk into a room. Choose the right one, style it well and fit it neatly, and the whole room comes together around it. Here's how we'd go about it, from first ideas to the finished fireplace.

Part 1: Styling your room around the fireplace

Let the fireplace be the focal point

Arrange your seating so the fireplace is the natural place to look. In most living rooms that means a sofa facing the fire, with chairs either side. If the TV has to share the wall, a media wall or media suite brings the two together neatly rather than having them compete.

Match the surround to your home

The style of your house is the best starting point. A classic fire surround with corbels and mouldings suits Victorian and Edwardian rooms with high ceilings. A simple classic design is often the easiest way to update a 1930s to 1970s fireplace. In new builds and modern flats, modern fire surrounds with flat fronts and square edges keep things clean and uncluttered. For cottages and barn conversions, solid oak brings warmth and real grain.

Get the scale right

A surround that's too small looks lost on the chimney breast, and one that's too big can overpower the room. Leave a little wall showing on each side of the shelf, and make sure your hearth is wider than the surround's legs. Our guide on how to measure for a fire surround walks you through it, and if none of our sizes fit, any surround can be made to measure for £95, or £190 for larger sizes.

Choose a colour that works with your walls

  • White and cream brighten a dark room and suit almost any wall colour.
  • Stone and soft greys sit happily in neutral schemes.
  • Black and charcoal make a bold focal point against a pale wall, or blend into a dark feature wall for a cosy, modern look.
  • Greens and heritage colours suit period and country homes.
  • Oak, walnut and mahogany tie in with wooden floors and furniture.

All our painted colours cost the same, and wood finishes are £45 extra. Colours never look quite the same on screen, so we always suggest ordering colour samples and holding them against your wall in daylight and lamplight.

Add the finishing touches

A hearth and back panel frames the fire and turns a surround into a complete fireplace. LED downlights under the shelf give a warm glow even when the fire is off, and a fireplace mirror adds light and height. On the shelf, keep it simple: a few larger pieces grouped in odd numbers look better than lots of small ornaments.

You can try different surrounds, colours, hearths, lights and fires together on our fire surround ideas mood board before you buy.

Part 2: Fitting your fire surround

Fitting one of our surrounds is very achievable for a confident DIYer, and any builder or joiner can do it for you. Every surround comes with our hidden fitting brackets, which hold it firmly against the wall without any visible fixings. If you're fitting a gas fire, use a Gas Safe registered engineer, and for open fires and stoves use a HETAS installer.

Before you start

  • Fit your hearth and back panel first. Our guide on how to fit a hearth and back panel explains how.
  • Make sure there's power within reach of the fire, and for downlights too.
  • Have a pencil, tape measure, drill and the right wall plugs and screws for your wall. These aren't supplied, as every wall is different.

Step by step

  1. Position the surround. Stand it on the hearth, usually central to the chimney breast, and measure from each edge of the chimney breast until both sides are equal.
  2. Mark the wall. Carefully pull one side a little away from the wall and pencil a mark just inside the edge of the surround, where it will be hidden. Do the same on the other side, then move the surround away.
  3. Fix the wall brackets. Measure 30mm in from each mark towards the centre. This is where the edge of each wall bracket goes. Fix them halfway between the shelf and the fire opening, as high as you can. On plasterboard, find a wooden batten to screw into.
  4. Fit the brackets to the surround. Slide the right-angle bracket down behind the wall bracket, measure from the hearth to its screw holes, and mark the same height inside the back of each leg. Screw the brackets to the inside of the legs, using the centre of the slotted holes so you can adjust them.
  5. Hang the surround. Lift it onto the wall brackets. If it needs to sit tighter, take it down, loosen the brackets slightly, move them back and re-hang it.

The brackets are designed to stop the surround falling forward, so you don't need to worry about getting everything perfectly level. Our fitting kit guide has diagrams and a video if you'd like to see it done.

Need a hand?

Whether you're choosing a colour, checking a size or halfway through fitting, we're happy to help. Call us on 01422 250 723, Monday to Friday, 10am to 4pm.

Back to blog